My Cart: 0 item(s)
$68.95
BlackTip Jetsports Sheet Goods Dark Blue-Adhesive
Brand: BlackTip Jetsports
SKU #: 130BT011
Shipping Weight: 6.00 pounds
Quantity in Basket:
None
All sizes are approximate.
Dark Blue: 39"x78" and about a 1/4" thickness
BlackTip Jetsports Traction Mat Sheet Goods include PSA and are in stock and usually available for same day shipping.
Cut Groove: Black, Black Marble, White Granite, Lime Green, Blue Marble, Dark Blue, Red, Orange, Yellow, Purple Marble, White Camo and Slate Gray
Two-Tone Cut Groove: Neon Green/Black, Aegean Blue/Black, Slate Gray/Black, Red/Black
Wishbone: Black, Gray and Purple
Diamond Plate: Black, Purple and Gray.
Sheet sizes:
All except red, yellow and orange: 39"x78" and about a 1/4" in thickness
Red, orange and yellow: 45” x 90” x 1/4” thickness
Two-Tone Neon Green/Black, Aegean Blue/Black, Slate Gray/Black, Red/Black: 43”x83”x 1/4": thickness
We also offer an alternative BlackTip Jetsports Traction Mat Sheet Good without PSA, available upon special request.
Watercraft Superstore's BlackTip Jetsports traction mats have a 1 year manufacturer?s warranty against defect in material and workmanship. This warranty does not cover fading, tearing or stains due to user negligance. We do our best to make sure every traction mat set is perfect, but sometimes things happen.
If you should have a problem, please contact Watercraft Superstore @866-957-9277 or sales@watercraftsuperstore.net to identify your issue.
If you should have a problem, please contact Watercraft Superstore @866-957-9277 or sales@watercraftsuperstore.net to identify your issue.
Removal of original riveted mats :Drill the heads off of the rivets holding down the original mats while pushing the remaining rivet into the hull. Fill the holes left by the rivet with 5min. epoxy, this can be purchased locally at any auto parts store. Make sure to scrape the epoxy flat in the foot wells so the new mats will lay flush. Clean the area that the new mats will be attached to with acetone solvent for proper adhesion.
Removal of original glue down mats:By hand, peel off any old mat material that you are able to and then you use a putty knife to help remove all material from the difficult areas. Areas that are difficult may require spraying WD-40 brand lubricant in between the mat and hull to help loosen the old adhesive. Take your time on the prep work; this is important to achieve professional results.
Now that your surface is clean and ready for the new mats it is time to lay out how your mats will look in the foot wells. This is the location the mats will be attached. Trace around the mats using a pencil. This is your reference area to place the mats after the paper is peeled off the back of the mat.
Peel off the paper backing from the mat and line up one end of the mat to your traced out area. (Do Not Try to Install the complete mat in one shot) Slowly work the mat down into your outline.
After the entire mat is installed you must apply even pressure down on top of the mat to insure complete contact to the hull.
Let mats sit for 12 hrs after the install so the glue will fully cure.
Removal of original glue down mats:By hand, peel off any old mat material that you are able to and then you use a putty knife to help remove all material from the difficult areas. Areas that are difficult may require spraying WD-40 brand lubricant in between the mat and hull to help loosen the old adhesive. Take your time on the prep work; this is important to achieve professional results.
Now that your surface is clean and ready for the new mats it is time to lay out how your mats will look in the foot wells. This is the location the mats will be attached. Trace around the mats using a pencil. This is your reference area to place the mats after the paper is peeled off the back of the mat.
Peel off the paper backing from the mat and line up one end of the mat to your traced out area. (Do Not Try to Install the complete mat in one shot) Slowly work the mat down into your outline.
After the entire mat is installed you must apply even pressure down on top of the mat to insure complete contact to the hull.
Let mats sit for 12 hrs after the install so the glue will fully cure.
Use only mild dishwashing soap to clean your mats, if you must clean grease from the mats we suggest using Simple Green brand cleaner only to do so.
