$252.95
Solas ABC Impeller for Sea-Doo SD-SC-A (13-18)
Brand: Solas
SKU #: 607SO068
Shipping Weight: 4.00 pounds
Quantity in Basket:
None
Super Camber A-B-C-D-E - For a Cost Effective Solution. The Super Camber A-B-C-D-E series remains one of the most popular products in the personal watercraft market. The Super Camber blade has increased flow and the thrust of the impeller.
WARNING: This product can expose you to chemicals which are knownn to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to https://www.P65Warnings.ca.gov.
140mm Diameter Pump
1991 XP
1992 XP
1993 SPX
1993 SPI
1994 SPI
1995 SPI
1996 SPI
1988 SP
1989 SP
1990 SP
1991 SP
1992 SP
1993 SP
1994 SP
1995 SP
1996 SP
1992 GSX
1993 GSX
1992 GTX
1993 GTX
1992 GTS
1993 GTS
1994 GTS
1995 GTS
1996 GTS
1990 GT
1991 GT
1991 XP
1992 XP
1993 SPX
1993 SPI
1994 SPI
1995 SPI
1996 SPI
1988 SP
1989 SP
1990 SP
1991 SP
1992 SP
1993 SP
1994 SP
1995 SP
1996 SP
1992 GSX
1993 GSX
1992 GTX
1993 GTX
1992 GTS
1993 GTS
1994 GTS
1995 GTS
1996 GTS
1990 GT
1991 GT
1.)Remove and separate the whole jet pump from the PWC
2.)Remove the trail cone (or cap) from the stator
3.)Hold the rear end of the shaft with a bench vise. Remove the impeller with an impeller wrench. Turning counter clockwise will loosen the impeller.
4.)Visually inspect thread on shaft and impeller for debris or damage. Apply grease or anti-seize on the thread before installation.
5.)Screw the impeller by hand; please be careful of the sharp edge of the impeller. Tighten with the impeller wrench. If the impeller feels too tight or not threaded properly, unscrew the impeller, clean and check the thread.
6.)Assemble the pump and refill O/E pump oil or grease to spec.
*this installation guide is suggested for reference only
*please refer to your original service manual or contact your PWC dealer for detail
*guide provided by Solas
*some wrenches are optional parts and are available for purchase on our website
2.)Remove the trail cone (or cap) from the stator
3.)Hold the rear end of the shaft with a bench vise. Remove the impeller with an impeller wrench. Turning counter clockwise will loosen the impeller.
4.)Visually inspect thread on shaft and impeller for debris or damage. Apply grease or anti-seize on the thread before installation.
5.)Screw the impeller by hand; please be careful of the sharp edge of the impeller. Tighten with the impeller wrench. If the impeller feels too tight or not threaded properly, unscrew the impeller, clean and check the thread.
6.)Assemble the pump and refill O/E pump oil or grease to spec.
*this installation guide is suggested for reference only
*please refer to your original service manual or contact your PWC dealer for detail
*guide provided by Solas
*some wrenches are optional parts and are available for purchase on our website
Impeller Series | Wrench | Seal |
SD Super Camber (ABC Series) | WR001 | SL007 |
SD Super Camber (IJK Series) | WR001 | SL007 |
SD, ST Xprop Series | WR001 | SL007 |
SD, SF, ST Concord Series | WR001 | SL007 |
ST Dynafly Series | WR001 | SL007 |
SR Concord Series | WR011 | SLA011 (24mm shaft) |
SRZ, SRX Concord Series | WR012 | SLA012 |
