My Cart: 0 item(s)
$252.95
Solas Xprop Impeller for Yamaha YB-SC-X (15-18)
Brand: Solas
SKU #: 607SO134
Shipping Weight: 4.00 pounds
Quantity in Basket:
None
X-prop - High Speed & Ultimate Performance
The SOLAS X prop gives you the most powerful propulsion in the water from an advanced design that incorporates a high compression hub and cambered blades.
Enthusiasts looking for speed and acceleration from the novice to the professional will be satisfied using this impeller.
You can trust the harsh field testing of the X prop by Team SOLAS.
1997 - 2000 Wave Runner GP 760
1994 - 1997 Wave Raider
1994 - 1997 Wave Deluxe
1994 - 1997 Wave Venture
1993 - 1997 Pro VXR
1994 - 1997 Wave Raider
1994 - 1997 Wave Deluxe
1994 - 1997 Wave Venture
1993 - 1997 Pro VXR
1.)Remove and separate the whole jet pump from the PWC
2.)For YH Series impeller, remove the trail cone (or cap) from the stator. For all others, hold the front end of the drive shaft with a shaft holder (optional part) on bench vise.
3.)Hold the rear end of the shaft with a bench vise. Remove the impeller with an impeller wrench (optional part). Turning counter clockwise will loosen the impeller.
4.)Visually inspect thread on shaft and impeller for debris or damage. Apply grease or anti-seize on the thread before installation.
5.)Screw the impeller by hand; please be careful of the sharp edge of the impeller. Tighten with the impeller wrench. If the impeller feels too tight or not threaded properly, unscrew the impeller, clean and check the thread.
6.)Assemble the pump and refill O/E pump oil or grease to spec. (for YH series assemble the pump and put it back on the PWC)
*this installation guide is suggested for reference only
*please refer to your original service manual or contact your PWC dealer for detail
*guide provided by Solas
*some wrenches are optional parts and are available for purchase on our website
2.)For YH Series impeller, remove the trail cone (or cap) from the stator. For all others, hold the front end of the drive shaft with a shaft holder (optional part) on bench vise.
3.)Hold the rear end of the shaft with a bench vise. Remove the impeller with an impeller wrench (optional part). Turning counter clockwise will loosen the impeller.
4.)Visually inspect thread on shaft and impeller for debris or damage. Apply grease or anti-seize on the thread before installation.
5.)Screw the impeller by hand; please be careful of the sharp edge of the impeller. Tighten with the impeller wrench. If the impeller feels too tight or not threaded properly, unscrew the impeller, clean and check the thread.
6.)Assemble the pump and refill O/E pump oil or grease to spec. (for YH series assemble the pump and put it back on the PWC)
*this installation guide is suggested for reference only
*please refer to your original service manual or contact your PWC dealer for detail
*guide provided by Solas
*some wrenches are optional parts and are available for purchase on our website
Impeller Series | Wrench | Holder | Seal |
YA Super Camber (ABC/IJK Series) | WR003 | WR003H | SL003 |
YB Super Camber (IJK Series) | WR004 | WR004H | SLA008 (18mm shaft) |
YD Super Camber Series (IJK Series) Xprop Series | WR004 | WR004H | SLA008 |
YD Concord Series | WR007 | WR007H | SLA009A |
YF Concord/Xprop Series | WR007 | WR007H | SLA009 |
YG Dynafly Series | WR007 | WR007H | SLA009 |
YS Dynafly Series | WR014 | WR014H | SLA014 |
YS Concord Series | WR014 | WR014H | SLA016 |
YH Concord Series (only for 2005-06 VX110 Sport and VX700 2006) | WR001 |
| SLA009 |
